[phpBB Debug] PHP Notice: in file /viewtopic.php on line 988: date(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected 'Europe/Moscow' for 'MSD/4.0/DST' instead
[phpBB Debug] PHP Notice: in file /viewtopic.php on line 988: getdate(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected 'Europe/Moscow' for 'MSD/4.0/DST' instead
SolaraGuy.com • View topic - noise
Page 1 of 1

noise

PostPosted: Fri Apr 02, 2010 4:41 pm
by 5842solara
hey, i just installed a supercharger.. i dont know if it even works though..

well.. there is a noise coming for the sc.. i think the pulley side maybe.. it has the whine that sc makes but its an ugly whine. how do you lubricate the sc? do you put oil.. i know its pre lubed but can you add more? thanks

or.. is the sc just broken?

PostPosted: Fri Apr 02, 2010 4:51 pm
by GzNutz
Can you post a vid?

PostPosted: Fri Apr 02, 2010 5:00 pm
by 5842solara
i can try, not sure how though. i dont have a youtube account or anything.
well i have to go to the store though to get o rings.. my injectors leaking. i dontk now when i can take vid.

um.. also

i read that the ebc cuts boost from 1st to 2nd... it helps the trans from breaking? (automatic) but what about standard cars? do i need the ebc on a standard car?

PostPosted: Sat Apr 03, 2010 12:55 am
by 5842solara
thanks Gznutz, but i found the problem..
after i fixed the fuel leak, i was able to run the car.
the tension pulley is moving a lot. and when i hold it by hand it kinda goes away.

PostPosted: Sat Apr 03, 2010 1:24 am
by jetbtkng
maybe your belt is to big, try a size smaller................. :drinking:

PostPosted: Sat Apr 03, 2010 2:55 pm
by 5842solara
I dont think its the belt though. because the squeaking sounds like the bearing is no good. and the tension is preetty good..

PostPosted: Sat Apr 03, 2010 4:51 pm
by 5842solara
ah stupid.. it was hitting the stock stud from the old motor mount bracket. but damn im running lean and egr sensor circuit code is coming up

PostPosted: Sun Apr 04, 2010 4:53 pm
by ToyoSolV6
get tuned kid!

cnt run lean, your gonna hurt something....FAST!

PostPosted: Sun Apr 04, 2010 5:27 pm
by 5842solara
ToyoSolV6 wrote:get tuned kid!

cnt run lean, your gonna hurt something....FAST!


yeah.. im trying to find a safc.. but i dont want to spend like 2 or 3 bils on ebay..

PostPosted: Sun Apr 04, 2010 5:31 pm
by jetbtkng
well thats what there going for, if u look hard enough u might find one for about $150-175, but i wouldnt run without it very long........... :drinking:

PostPosted: Sun Apr 04, 2010 6:02 pm
by 99BlackSandv6
You're probably leaking air through the EGR piping. That will throw the code, and cause very lean conditions. Check all your mating surfaces and gaskets, make sure it's all buttoned up tight.

PostPosted: Tue Apr 06, 2010 1:01 am
by 5842solara sc
99BlackSandv6 wrote:You're probably leaking air through the EGR piping. That will throw the code, and cause very lean conditions. Check all your mating surfaces and gaskets, make sure it's all buttoned up tight.



hmm.. I did some re-hosing.. The supercharger has 1 diagram on hosing..
and the ebc wiring diagram had another. I did it the ebc way and now the code went away.