2007 LED Taillight Conversion
Posted: Wed Aug 09, 2006 3:13 pm
What you need-
2007 Taillights (OF COURSE)-
Electrical Tape, Wire cutters, and all your crimpers with all that good stuff-
2x Load Resistors OR 1 LED Flasher Relay
Link http://superbrightleds.com/tail-brake-turn.html
Load Resistors Kits of 6 OHMS 50 Watts (one for each light)-
1 OR 2 Light Converters (Depending on how hard you wanna work with the wires, I used 2, one for each light) which will be...
The Hopkins Towing Solutions Basic 4 Wire Harness
Part Number 48915..... These are like 15 bucks each... Walmart, Online or any Store that sells Auto Accesories.
-
Also there are adapters that they sell that will go into the open end, make sure you buy the one that fits in with 3 male and 1 female end on one side and it comes with 4 wires at the other....................
PART No 48205
The relay or resistors are to avoid the fast blinker effect**
The converter is what is going to make the lights be 3 functions... brake/ parking light/ signal**
Okay there are wires you are going to cut and reconnect (I AM NOT RESPONSIBLE IF YOU MESS YOUR CAR UP!!)
Brake Light Wire (Cut)-
Ground which is White (Do not cut)-
Parking Light Wire (cut)-
Reverse Light (Will not be cut. Just Pull the PIN out of the Connector and switch it around with the Signal)-
Signal Light (Which is now unuseable will be cut)
**(Remember to leave enough wire to connect together)
UNfortunately I dont remember what color the wires are, so grab an electrical tester to find out, and write it down on a paper so you won't forget.
Now that the wires are cut, Grab your Converter attached to the Adapter and connect the wires together from the car to the converter...
Signal Right is Green on the Converter
Brake is RED
Left is YELLOW
Parking Light is Brown
Now from the Converter to your Light
Yellow is Left Signal
Brown is Parking Light
Green is Right Signal
***Note.. You will not use the Ground coming from the converter(s) so leave it untouched. Also if you end up using 2 converters, on the right side you will Not use the Yellow wire and on the Left you will not use the Green***
Last but not least the Resistors come with splice taps, you will connect it to the Ground wire from the lights and the other end to the Signal Wire before the Converter. (If you connect it after the converter you will get a fast blinker when you brake.) Also now is the time to doubleside sticky the Resistor on the inside of the car, make sure it doesnt touch the carpet from where you mount it.....
If you buy the Relay just Switch it out with the stock one and avoid the the resistors.
Finished Result...
http://video.google.com/videoplay?docid ... 5718673811
Enjoy your Lights.....
-Pedro Milt Machete
2007 Taillights (OF COURSE)-
Electrical Tape, Wire cutters, and all your crimpers with all that good stuff-
2x Load Resistors OR 1 LED Flasher Relay
Link http://superbrightleds.com/tail-brake-turn.html
Load Resistors Kits of 6 OHMS 50 Watts (one for each light)-
1 OR 2 Light Converters (Depending on how hard you wanna work with the wires, I used 2, one for each light) which will be...
The Hopkins Towing Solutions Basic 4 Wire Harness
Part Number 48915..... These are like 15 bucks each... Walmart, Online or any Store that sells Auto Accesories.
-
Also there are adapters that they sell that will go into the open end, make sure you buy the one that fits in with 3 male and 1 female end on one side and it comes with 4 wires at the other....................
PART No 48205
The relay or resistors are to avoid the fast blinker effect**
The converter is what is going to make the lights be 3 functions... brake/ parking light/ signal**
Okay there are wires you are going to cut and reconnect (I AM NOT RESPONSIBLE IF YOU MESS YOUR CAR UP!!)
Brake Light Wire (Cut)-
Ground which is White (Do not cut)-
Parking Light Wire (cut)-
Reverse Light (Will not be cut. Just Pull the PIN out of the Connector and switch it around with the Signal)-
Signal Light (Which is now unuseable will be cut)
**(Remember to leave enough wire to connect together)
UNfortunately I dont remember what color the wires are, so grab an electrical tester to find out, and write it down on a paper so you won't forget.
Now that the wires are cut, Grab your Converter attached to the Adapter and connect the wires together from the car to the converter...
Signal Right is Green on the Converter
Brake is RED
Left is YELLOW
Parking Light is Brown
Now from the Converter to your Light
Yellow is Left Signal
Brown is Parking Light
Green is Right Signal
***Note.. You will not use the Ground coming from the converter(s) so leave it untouched. Also if you end up using 2 converters, on the right side you will Not use the Yellow wire and on the Left you will not use the Green***
Last but not least the Resistors come with splice taps, you will connect it to the Ground wire from the lights and the other end to the Signal Wire before the Converter. (If you connect it after the converter you will get a fast blinker when you brake.) Also now is the time to doubleside sticky the Resistor on the inside of the car, make sure it doesnt touch the carpet from where you mount it.....
If you buy the Relay just Switch it out with the stock one and avoid the the resistors.
Finished Result...
http://video.google.com/videoplay?docid ... 5718673811
Enjoy your Lights.....
-Pedro Milt Machete